700R4 & 4L60E Automatic transmissions specialists - ProBuilt
Search: Advanced search
Select language:
Printable version 
Categories Categories
4T65E (HD) Upgrades & Transmissions
Computer Controls (MagnaShift)
Buy just what you need
Books and Videos
Ford Rebuild Kits
GM Rebuild Kits
Mopar Rebuild Kits
700R4 Upgrades
4L60E Upgrades
4L60E & LS1 Upgrades
4L80E Upgrades
TransGo Performance Shift Kits
TransGo Shift Kits
GM Edge Torque Converters
GM Circle "D" Torque Converters
Ford Transmissions
GM Transmissions

Bestsellers Bestsellers
1. 4L60E Heavy Duty 1993-1997
2. LS1/4L60E Pro Street 1998&Up
3. LS1/4L60E Heavy Duty 1998 & Up
4. 4L60E Street/Strip 1993-1997
5. 4L60E Pro Street 1993-1997

Manufacturers Manufacturers
Vigilante Torque Converter
Stallion Torque Converter
Edge Torque Converter
Continental Torque Converters

Special Special
Gift certificates

Help Help
Contact us
Privacy statement
Terms & Conditions

Pro-Built Automatics :: GM Transmissions :: General Motors :: 4L60E :: 4L60E Street/Strip 1993-1997

4L60E Street/Strip 1993-1997
4L60E Street/Strip 1993-1997 
This is a one piece case/bell housing assembly. If you have the bolt-on bell housing, please specify.

Starting at the "Front Pump", new (late design) seal, Teflon bushing, 10-vane rotor/slide assembly on 1993-1996 transmissions, and 13-vane rotor/slide assembly on 1997 and up transmissions. Trans-Go steel rings & priming spring, Trans-Go HD pressure regulator spring and bumper spring, Trans-Go .532/.500 boost valve, both halves of pump machined flat with rotor and slide to pump clearance set at .002"- .003". A new stator support is installed. This pump now will keep the pressure & volume up 7,800 rpm.

Reverse Input Drum: A new reverse/input drum, along with the Turbulator low-drag steels, and Borg Warner clutches. The Belville spring is replaced with a waved spring, this eliminates the Belville spring from eating the reverse/input drum.

Input Drum: The stock input drum starts getting into trouble at around 550 HP with a 10" or smaller diameter torque converter. I rework the input drum in the overrun piston area by adding a steel sleeve and special machining of the overrun piston to prevent splitting the drum open from high loads. New latest design 29 element input sprag, Borg Warner clutches for the overrun and late design Borg Warner forward clutch assemblies, 8 Borg Warner Hi-Energy clutches along with Kolene steels used in the 3-4 clutch pack, Trans-Go (Hi-Rev) heavy duty springs replace the OEM 3-4 and forward springs and 3-4 helper springs (the Trans-Go springs prevent the 3-4 clutches from getting into trouble, due to centrifugal clutch apply. Good for up to 7,800 rpm, stock setup starts getting into trouble at around 5,000 rpm), clearance for the 3-4 clutch pack .025" -.035". New 3-4 molded piston installed. Turbulator overrun steels are added for a slight gain in gas mileage. A "dual feed" input shaft capsule is installed for a better torque converter clutch lockup on 1993 and 1994 transmissions.

Rear Drive Section: Hand picked input sun gear, forward planet with batwing thrust washers, input internal gear, reaction carrier shaft, a new Sealed Power Beast sun shell, the latest design Borg Warner low/reverse roller assembly. Turbulator low-drag steels, Borg Warner clutches, hand picked, or new rear planet, hand picked reaction sun gear, internal reaction gear, internal reaction gear support, a bronze rear case bushing, Teflon extension housing bushing, and a Vamac (prelubed) rear seal.

2-4 Band & 2-4 Servo: Borg Warner Hi-Energy 2-4 band, new Corvette 2nd gear apply servo used in conjunction with the latest design Viton seals. An additional spring is added to the cushion side of the servo to help provide a smoother 1-2 apply at light throttle while still allowing a firm WOT shift.

Valve Body: We use the Trans-Go Performance Shift kit (modified) in conjunction with the large boost valve, Corvette servo, and the 8 clutch 3-4 pack. (This setup has proven to be the most reliable). We work with the accumulators to give the best possible part throttle shifts, and progressively firmer shifts with more throttle opening. A Sealed Power (zero-leak) filter is used.

Part Number 4L60SS93-97
Price: $2,395.00

Engine Type

Add to cart



Your cart Your cart
Cart is empty

View cart
Wish list
Orders history

Authentication Authentication
Secure login 
Recover password

If Javascript is disabled in your browser click here

Powered by Primeaus Web design Design by Primeaus.com - Copyright © 2004-2018 Pro-Built Automatics